BOHLER DMO-IG TIG Rods Importer, Stockist & Supplier Worldwide
Shanti Metal Supply Corporation (SMSC) is an importer, stockist, supplier and worldwide exporter of BOHLER DMO-IG TIG Rods for industrial welding, fabrication, power generation, pressure equipment, piping, engineering and maintenance requirements. SMSC supports industrial customers, contractors, fabricators, distributors and project procurement teams across the Gulf countries, Indonesia, Malaysia and other international markets.
BOHLER DMO-IG is a low-alloyed, creep-resistant TIG rod and wire designed for suitable gas tungsten arc welding (GTAW) applications where appropriate mechanical properties and elevated-temperature performance are required. The product is classified under AWS A5.28 / SFA-5.28 ER70S-A1 TIG Rods, with ER80S-G also referenced, and under EN ISO 21952-A W MoSi TIG Rods.
For buyers searching for a BOHLER DMO-IG TIG Rod importer, BOHLER DMO-IG stockist, BOHLER DMO-IG supplier or BOHLER DMO-IG exporter, SMSC provides specification-based supply support for domestic and international industrial requirements.
Quick Answer: What Are BOHLER DMO-IG TIG Rods?
BOHLER DMO-IG TIG Rods are low-alloyed, creep-resistant welding rods and wires used for suitable GTAW/TIG applications involving compatible alloy steels, pressure equipment, piping, power-generation components and selected elevated-temperature service applications. The product is identified under AWS A5.28 / SFA-5.28 ER70S-A1 TIG Rods, with ER80S-G also referenced, and EN ISO 21952-A W MoSi.
BOHLER DMO-IG TIG Rods – Product Overview
BOHLER DMO-IG is a TIG rod and wire intended for manual and mechanized gas tungsten arc welding. It is designed as a low-alloyed, creep-resistant welding consumable for suitable applications where weld-metal strength, ductility and elevated-temperature performance are important considerations.
The filler metal contains molybdenum as an important alloying addition and is intended for suitable welding applications involving creep-resistant steels and other compatible steel grades. Selection of the filler metal should always consider the base material, service temperature, joint design, welding procedure and applicable project specification.
Technical product information indicates suitability for selected creep-service applications at design temperatures up to approximately 550°C, subject to the applicable engineering, material and welding requirements.
For international industrial buyers looking for a BOHLER DMO-IG TIG Rod importer, BOHLER DMO-IG stockist, ER70S-A1 TIG rod supplier, creep-resistant TIG welding consumable supplier or BOHLER welding rod exporter, SMSC can support enquiries based on product size, quantity and delivery destination.
BOHLER DMO-IG TIG Rods Specifications
| Property | Specification / Information |
|---|---|
| Product Name | BOHLER DMO-IG |
| Brand | BOHLER |
| Product Form | TIG Rod / TIG Wire |
| Welding Process | GTAW / TIG |
| Product Category | Low-Alloyed, Creep-Resistant Welding Consumable |
| AWS Classification | AWS A5.28 / SFA-5.28 ER70S-A1 (ER80S-G) |
| EN ISO Classification | EN ISO 21952-A W MoSi |
| Molybdenum | Approximately 0.5% typical reference value |
| Polarity | DC Negative / DCEN for applicable GTAW operation |
| Shielding Gas | Argon, subject to applicable welding procedure |
| Service Application | Creep-Resistant and Elevated-Temperature Welding Applications |
| Business Type | Importer, Stockist, Supplier & Worldwide Exporter |
| Primary Export Focus | Gulf Countries |
| Other Export Markets | Indonesia, Malaysia & Other Worldwide Markets |
BOHLER DMO-IG Classification and Standards
Correct identification of welding consumables is important for procurement, welding procedure qualification and project documentation. BOHLER DMO-IG is identified under internationally recognized filler-metal classification systems.
| Standard | Classification |
|---|---|
| AWS A5.28 / SFA-5.28 | ER70S-A1 (ER80S-G) |
| EN ISO 21952-A | W MoSi |
| Product Type | Low-Alloyed, Creep-Resistant TIG Rod / Wire |
| Welding Process | GTAW / TIG |
Typical Chemical Composition of BOHLER DMO-IG TIG Rods
The following values are provided as typical technical reference information. Chemical composition may vary according to the applicable product specification and batch. For project-critical applications, buyers should verify the current manufacturer technical documentation and material certificate for the specific product supplied.
| Element | Typical Content (wt. %) |
|---|---|
| Carbon (C) | 0.10 |
| Silicon (Si) | 0.60 |
| Manganese (Mn) | 1.10 |
| Molybdenum (Mo) | 0.50 |
| Balance | Iron and residual elements |
Mechanical Properties of BOHLER DMO-IG All-Weld Metal
Mechanical properties depend on welding conditions and heat-treatment condition. Published product information provides typical properties for applicable as-welded and stress-relieved conditions.
| Condition | Yield Strength Rp0.2 | Tensile Strength Rm | Elongation | Impact Energy at +20°C | Impact Energy at -30°C |
|---|---|---|---|---|---|
| As Welded | Typical 530 MPa | Typical 650 MPa | Typical 26% | Typical 180 J | Typical 100 J |
| Stress Relieved at 620°C / 1 h | Typical 480 MPa | Typical 585 MPa | Typical 27% | Typical 210 J | Typical 180 J |
The above values are technical reference values for all-weld metal. Actual results can vary according to welding conditions, shielding gas, heat input, joint design, welding position and applicable heat treatment.
Suitable Base Materials for BOHLER DMO-IG TIG Rods
BOHLER DMO-IG is intended for suitable welding applications involving creep-resistant steels, cast steels and selected structural, fine-grained and pipeline steels. The suitability of a filler metal must be confirmed against the exact base-material grade and applicable welding procedure.
| Material / Application Category | Examples |
|---|---|
| Creep-Resistant Steels | 16Mo3 and similar compatible alloyed steels |
| Pressure and Boiler Applications | Selected pressure-vessel and boiler steels |
| Pipeline Steels | Suitable pipeline and line-pipe steel applications |
| Structural Steels | Selected high-strength and fine-grained steels |
| Steel Castings | Suitable similar-alloyed cast steels |
Welding Parameters for BOHLER DMO-IG TIG Rods
BOHLER DMO-IG welding parameters should be selected according to rod diameter, base-metal thickness, joint preparation, welding position, heat input and the qualified welding procedure. The following values are general starting references and should be validated against the applicable WPS before production welding.
GTAW / TIG Reference Parameters
| Rod Diameter | Typical Amperage Range | Polarity | Shielding Gas |
|---|---|---|---|
| 1.6 mm | 60–120 A | DC Negative | Argon |
| 2.0 mm | 80–150 A | DC Negative | Argon |
| 2.4 mm | 100–200 A | DC Negative | Argon |
| 3.0 mm | 140–250 A | DC Negative | Argon |
| 3.2 mm | 160–280 A | DC Negative | Argon |
Preheating, Interpass Temperature and Post-Weld Heat Treatment
Preheating, interpass temperature and post-weld heat treatment should be selected according to the base material and applicable welding requirements. Published technical information indicates that preheating may be recommended within approximately 100°C to 250°C, depending on wall thickness, material condition and application requirements.
Post-weld heat treatment may be required depending on the base material, thickness, service conditions and applicable engineering specification. Technical information may reference temperatures in the approximate range of 530°C to 620°C. The approved WPS, project specification and applicable code should always take priority for production welding.
Applications of BOHLER DMO-IG TIG Rods
- Boiler and pressure-equipment fabrication
- Power-generation and energy-industry welding
- Creep-resistant steel welding
- Elevated-temperature service applications
- Industrial piping and pipeline fabrication
- Pressure-vessel manufacturing
- Engineering and heavy-fabrication projects
- Structural and fine-grained steel applications
- Maintenance and repair of suitable alloy-steel components
- Manual and mechanized GTAW applications
Advantages of BOHLER DMO-IG TIG Rods
- Low-alloyed creep-resistant weld-metal design.
- Suitable for selected elevated-temperature applications.
- Typical weld-metal chemistry includes approximately 0.5% molybdenum.
- Suitable for manual and mechanized GTAW applications.
- Provides favorable mechanical properties under applicable welding conditions.
- Available in multiple rod diameters subject to product availability.
- Suitable for selected pressure, boiler and piping applications.
- Suitable for international industrial procurement requirements.
- Identified under established international welding classification standards.
Available Sizes of BOHLER DMO-IG TIG Rods
TIG rod dimensions can vary according to product form, manufacturer packaging and market availability. Common sizes referenced for BOHLER DMO-IG include the following. Availability should be confirmed at the time of enquiry.
| Diameter | Typical Length | Product Form |
|---|---|---|
| 1.6 mm | 1000 mm | TIG Rod |
| 2.0 mm | 1000 mm / selected supply lengths | TIG Rod |
| 2.4 mm | 1000 mm | TIG Rod |
| 3.0 mm | 1000 mm | TIG Rod |
| 3.2 mm | 1000 mm | TIG Rod |
Storage and Handling of BOHLER DMO-IG TIG Rods
TIG filler rods should be stored in suitable conditions to help protect them from moisture, dust, oil, grease and other contamination. Keeping the welding consumable clean before use helps support consistent welding performance.
- Store rods in clean and dry conditions.
- Keep products protected from moisture and contamination.
- Maintain product identification and packaging where possible.
- Do not mix different filler-metal classifications.
- Verify product designation before welding.
- Follow applicable manufacturer handling recommendations.
BOHLER DMO-IG TIG Rods Exporter Worldwide
Shanti Metal Supply Corporation (SMSC) supports worldwide export enquiries for BOHLER DMO-IG TIG Rods. The company serves industrial buyers, engineering contractors, fabrication companies, distributors, maintenance companies and project procurement teams requiring welding consumables for international projects.
Although the Gulf region is a primary international market for SMSC, the company also supports enquiries from customers in Asia, Southeast Asia, Africa, Europe and other international markets, subject to product availability, commercial terms and applicable export requirements.
Customers can submit the required product designation, diameter, quantity and delivery destination so that product availability and international supply requirements can be reviewed.
BOHLER DMO-IG TIG Rods Supplier for Gulf Countries
SMSC has a particular supply focus on the Gulf countries, supporting industrial welding and fabrication requirements for power-generation, oil and gas, petrochemical, pressure-equipment, piping, engineering and maintenance projects.
- BOHLER DMO-IG TIG Rods Supplier in UAE
- BOHLER DMO-IG TIG Rods Supplier in Dubai
- BOHLER DMO-IG TIG Rods Supplier in Abu Dhabi
- BOHLER DMO-IG TIG Rods Supplier in Saudi Arabia
- BOHLER DMO-IG TIG Rods Supplier in Qatar
- BOHLER DMO-IG TIG Rods Supplier in Oman
- BOHLER DMO-IG TIG Rods Supplier in Kuwait
- BOHLER DMO-IG TIG Rods Supplier in Bahrain
BOHLER DMO-IG TIG Rods Supplier in Indonesia and Malaysia
SMSC also supports industrial enquiries from Indonesia and Malaysia. Industrial buyers, fabrication companies, engineering contractors, maintenance companies, distributors and procurement teams can submit their requirement with the exact product designation, rod diameter, quantity and delivery destination.
Why Choose Shanti Metal Supply Corporation (SMSC)?
- Importer and stockist for industrial welding-product requirements.
- Supplier and exporter supporting worldwide industrial enquiries.
- Primary international market focus on Gulf countries.
- Additional supply support for Indonesia and Malaysia.
- Worldwide export support subject to availability and export requirements.
- Support for bulk and project procurement requirements.
- Specification-based product enquiry support.
- Suitable support for industrial fabrication and engineering buyers.
How to Order BOHLER DMO-IG TIG Rods
To request availability, pricing or a quotation from Shanti Metal Supply Corporation (SMSC), provide the following information for accurate product identification and faster enquiry processing.
- Product Name: BOHLER DMO-IG
- Required Diameter: For example 1.6 mm, 2.0 mm, 2.4 mm or 3.2 mm.
- Required Quantity: Number of packs or total quantity required.
- Destination Country: UAE, Saudi Arabia, Qatar, Oman, Kuwait, Bahrain, Indonesia, Malaysia or another international destination.
- Application: Where applicable, provide the intended welding application, base material or project requirement.
- Documentation: Specify any required certificates, inspection documents, technical datasheets or project documentation.
Need BOHLER DMO-IG TIG Rods?
Contact Shanti Metal Supply Corporation (SMSC) for BOHLER DMO-IG TIG Rod availability, stock details, quotation and worldwide export requirements.
Frequently Asked Questions About BOHLER DMO-IG TIG Rods
What are BOHLER DMO-IG TIG Rods?
BOHLER DMO-IG is a low-alloyed, creep-resistant TIG rod and wire used for suitable GTAW welding applications involving compatible creep-resistant, structural, pressure and engineering steel applications.
What is the AWS classification of BOHLER DMO-IG?
BOHLER DMO-IG is identified under AWS A5.28 / SFA-5.28 as ER70S-A1, with ER80S-G also referenced in the product classification.
What is the EN ISO classification of BOHLER DMO-IG?
The product is identified under EN ISO 21952-A as W MoSi.
What is BOHLER DMO-IG used for?
BOHLER DMO-IG is used for suitable TIG/GTAW welding applications involving creep-resistant steels, pressure equipment, boilers, piping, power-generation components and selected engineering applications.
What is the typical chemical composition of BOHLER DMO-IG?
Typical reference chemistry includes approximately 0.10% carbon, 0.60% silicon, 1.10% manganese and 0.50% molybdenum, with iron and residual elements forming the balance. Exact chemistry should be verified against the applicable product documentation and certificate.
What welding process is used with BOHLER DMO-IG?
BOHLER DMO-IG is used for gas tungsten arc welding, commonly known as GTAW or TIG welding, including suitable manual and mechanized applications.
What shielding gas is used for BOHLER DMO-IG TIG welding?
Argon is referenced as the shielding gas for applicable GTAW operation. The exact shielding-gas specification should follow the approved welding procedure and manufacturer recommendations.
Can BOHLER DMO-IG be used for elevated-temperature applications?
Yes. BOHLER DMO-IG is identified as a creep-resistant welding consumable, and published product information indicates suitability for selected creep-service applications at design temperatures up to approximately 550°C, subject to applicable engineering and welding requirements.
Who supplies BOHLER DMO-IG TIG Rods in Gulf countries?
Shanti Metal Supply Corporation (SMSC) is an importer, stockist and supplier supporting industrial enquiries for BOHLER DMO-IG TIG Rods, with a particular international supply focus on Gulf countries.
Does SMSC export BOHLER DMO-IG TIG Rods worldwide?
Yes. SMSC supports worldwide export enquiries for BOHLER DMO-IG TIG Rods, subject to product availability, quantity, destination and applicable international export requirements.
Does SMSC supply BOHLER DMO-IG TIG Rods to Indonesia and Malaysia?
SMSC supports industrial enquiries from both Indonesia and Malaysia. Customers can provide the required diameter, quantity and destination details for product availability and international supply review.
What information is required to order BOHLER DMO-IG TIG Rods?
Buyers should provide the product name, required rod diameter, quantity, application where applicable, destination country and any required technical or inspection documentation.
Our Other Products
Explore our range of high-quality products designed for industrial and engineering applications.
Conclusion
BOHLER DMO-IG TIG Rods are low-alloyed, creep-resistant welding consumables intended for suitable GTAW applications involving compatible alloy steels, pressure equipment, piping, power-generation and selected elevated-temperature service requirements. The product is identified under ER70S-A1 (ER80S-G) and EN ISO 21952-A W MoSi.
Shanti Metal Supply Corporation (SMSC) works as an importer, stockist, supplier and worldwide exporter of industrial welding products. The Gulf countries are a primary international market, while SMSC also supports customers in Indonesia, Malaysia and other worldwide markets.
Industrial buyers can submit their required BOHLER DMO-IG diameter, quantity, application and destination details to enquire about availability, stock and international supply.